More key & remote programing

Fiat/Alfa/Lancia key & remote programing

Seicento

1. Firstly obtain the 4 digit security code for the vehicle
2. Press the button (in the interior light assembly there is a button and an LED next to the alarm ultrasonic’s) for about a second and the LED will flash.
3. Release the button
4. After approx. 5 seconds the LED will flash once
5. Enter the first digit of the security code using the button as above.
6. Wait for about 5 seconds and the LED will flash once. Enter the second digit of the security code as above - if one of the digits is a zero, do not press the button at all and wait for the single flash requesting the next digit.
7. If all the numbers are entered correctly the LED will flash for 10 seconds whilst the LED is flashing, press and hold the button near the interior light (used above) The LED will continue to flash until you press a button of a remote - it should then remain on.
8. Release button of remote and the one in the interior light.
9. Repeat for subsequent remotes

Cinquecento

1. Firstly obtain the 4 digit security code for the vehicle
2. Press the button (in the interior light assembly there is a button and an LED next to the alarm ultrasonic’s) for about a second and the LED will flash.
3. Release the button
4. After approx. 5 seconds the LED will flash once
5. Enter the first digit of the security code using the button as above.
6. Wait for about 5 seconds and the LED will flash once
7. Enter the second digit of the security code as above - if one of the digits is a zero, do not press the button at all and wait for the single flash requesting the next digit.
8. If all the numbers are entered correctly the LED will flash for 10 seconds whilst the LED is flashing, press and hold the button near the interior light (used above)
9. The LED will continue to flash until you press a button of a remote - it should then remain on.
10. Release button of remote and the one in the interior light.

Bravo/Brava

1. Firstly obtain the 4 digit security code for the vehicle
2. Press the button (in the interior light assembly there is a button and an LED next to the alarm ultrasonic’s) for about a second and the LED will flash.
3. Release the button
4. After approx. 5 seconds the LED will flash once
5. Enter the first digit of the security code using the button as above. Wait for about 5 seconds and the LED will flash once
6. Enter the second digit of the security code as above - if one of the digits is a zero, do not press the button at all and wait for the single flash requesting the next digit.
7. If all the numbers are entered correctly the LED will flash for 10 seconds
whilst the LED is flashing, press and hold the right hand button near the
interior light (used above)
8. The LED will continue to flash until you press a button of a remote - it will
then remain on.
9. Release button of remote and the one in the interior light.

Coupe/Barchetta

1. Firstly obtain the 4 digit security code for the vehicle
2. Press button (in the interior light assembly there is a button and an LED next to the alarm ultrasonic’s) for about a second and the LED will flash.
3. Release the button
4. After approx 5 seconds the LED will flash once
5. Enter the first digit of the security code using the button as above.
6. Wait for about 5 seconds and the LED will flash once
7. Enter the second digit of the security code as above - if one of the digits is a zero, do not press the button at all and wait for the single flash requesting the next digit.
8. If all the numbers are entered correctly the LED will flash for 10 seconds whilst the LED is flashing, press and hold the right hand button near the interior light (used above)
9. The LED will continue to flash until you press a button of a remote - it will then remain on.
10. Release button of remote and the one in the interior light.

Ulyssee

New remotes cannot be programmed without the use of diagnostic equipment but existing remotes can be synchronised as follows :
1. Switch on the ignition
2. Press the lock or unlock button and hold for 10 seconds.

SCUDO

New remotes cannot be programmed without the use of diagnostic equipment but existing remotes can be synchronised as follows :
1. Switch on the ignition
2. Wait for the system LED to extinguish
3. Press the lock or unlock button and hold for 10 seconds, do this on all remotes to synchronise them.